Customize an Assmann Polyethylene Double Wall Tank System with Accessories That Fit Your Needs

Double wall tanks provide protection against hazardous chemical spills into the environment. Inner tank dome overlaps outer tank sidewall to prevent rainwater, snow and debris from entering into the containment basin. Our ability to heat trace and insulate make these tanks perfect for temperature sensitive chemicals. Molded-in lifting lugs and upper fitting flats are standard. Molded-in lower fitting flats, along with a sturdy Assmann designed bottom outlet, reduce the cost of expensive double wall outlets.  See our double wall tank accessories listed below.

      • Seismic restraint • Heat tracing and insulation
      • Wind-load restraint • Fiberglass reinforced ladder assemblies
      • Ultrasonic level device • Metallic nozzles
      • Reverse float level indicator • Top discharge with foot valve
      • Interstitial leak detection • Optional 21" and 24" manways
      • High-low level alarms • Bottom outlets


Accessories for Double Wall Tanks

Interstitial leak detection system with audible and visual alarms

Interstitial Leak Detection System

Designed with a NEMA 4X enclosure. Suitable for both indoor and outdoor applications. The control box is built from sturdy FRP construction with stainless steel lid hinge and clasp.

This system includes two-conductance type interstitial probes one acting as active; the other as ground. Both probes are equipped with 20 ft. of cable thus allowing the sensors to be placed low as possible in the interstitial area.

In most applications this system is mounted as high as possible on the secondary containment basin with a 2” bulkhead connection.

A single red flashing light is installed on the side of the NEMA enclosure that gives visual indication when a leak is detected, along with an audible horn that has an output of 2 ft. to be 68-80 dB. These alarms will give indication that the system has detected a leak requiring immediate attention.

An On/Off switch has been purposely left off the system so that when problems occur they cannot be ignore.

Accessories for Double Wall TanksReverse Float Level Indicator

Designed to show liquid level in the tank without having chemical outside the secondary containment. System has a large rotationally molded float that rides within the primary tank and a bright orange target that shows the liquid level on the exterior of the tank.

This design works in reverse. When the chemical tank is full, the exterior target will be at the base of the tank. When empty, the bright orange target is at the top of the tank, where clearly visible.

Accessories for Double Wall TanksFiberglass Reinforced Ladder Assemblies

FRP Ladders conform to OSHA requirements. Ladder assemblies are available in three configurations: ladder w/platform, straight ladder w/cage and ladder w/cage and platform.

These ladders are designed to terminate 48” below the tank roof. This allows personnel to view the roof of the tank, but deters them from walking on or entering the tank.


Ultrasonic Level Indicating Device

Liquid level indication with digital display in gallons.

 

Heat Tracing & Insulation

Available for use with temperature sensitive chemicals.

 

 

Accessories for Double Wall TanksDouble Wall Tank Metallic Nozzles

Assmann designed bottom outlets, along with molded-in lower fitting flats, reduce the cost of expensive double wall outlets. These all metallic nozzles available in 316 stainless steel, Titanium or Hastelloy C-276. These fittings provide the through tank wall connection for applications where tank cross section should not be exposed.

There are three types of nozzles available in nine sizes:

Male Fitting: Male pipe thread outside tank wall only.
Female Fitting: Female pipe thread inside and outside of tank wall.
Double Male Fitting: Male pipe thread inside and outside of tank wall.

The flange adapter and siphon drain (if applicable) can be applied to all three fitting types.

Model number availability and individual specifications subject to change without notice. Gallonage and weights are approximate. All wall thicknesses conform to ASTM D-1998.

               
        Assmann Corporation of America
        300 North Taylor Road, Garrett, IN 46738   USA
        Phone: 888-357-3181 • Fax: 888-Tank Fax (826-5329)
        Phone: 260-357-3181 • Fax: 260-357-3738
        E-mail: info@assmann-usa.com